1. Remove the black plastic

This can be done very easily with a screw driver. Just lower the door down and slide a flathead screwdriver down behind the plastic piece and very gently push forward.

Be very careful not to damage the soft bendable plastic, might want to wrap the screwdriver in tape first so it doesn’t scrap the plastic either.

I recommend placing the screwdriver in at one end, don’t try it in the middle.

It should pop out without much effort.

Pictures in the Gallery

2. Enter Service Mode

a. The printer should be plugged in but turned off.

b. Hold Stop/Reset button and Power button for 5 seconds

c. Release Stop/Reset button but continue to hold Power button

d. Press Stop/Reset twice

e. Release the Power Button

f. Wait for Copy Light to stop blinking before proceeding.

g. Press Stop/Reset button twice then Power this will print a simple ROM page.

h. Press Stop/Reset 5 times then power to select Destination.

i. Press Stop/Reset 4 times then Power to choose Euro.

j. Press Stop/Reset 1 or 2 times then power to print a simple ROM again and compare with first ROM print out. (try once first time through, may fix the tray rejection problem.)

k. Press Power button Twice to save settings.

3. Install the Driver

The USA driver will work just fine, it is on the CD that came with your printer. If the driver was already installed because you have been using the printer before you found this wonderful page, you will need to UNINSTALL it and RE-INSTALL it.

Advanced Option: How to change the Registry Key

4. Install Software

a. CDLabelPrint
b. Nero Cover Designer
c. Acoustica CD Label maker

CD Label Print is OK but some users would prefer other software to create there designs in so I have links to other software such as Nero Cover Designer and Acoustica. If you use Adobe there is a template for it as well: Adobe InDesign template

5. Purchase a Tray

You will need to purchase a tray for the printable cd or dvd to sit on. To know what Tray Letter you need simply look at the properties after you have finished:

Purchase a Canon cd tray on eBay. http://search.ebay.com/

Technorati : Canon MP600, cd print, instructions

1. Remove the black plastic

This can be done very easily with a screw driver. Just lower the door down and slide a flathead screwdriver down behind the plastic piece and very gently push forward.

Be very careful not to damage the soft bendable plastic, might want to wrap the screwdriver in tape first so it doesn’t scrap the plastic either.

I recommend placing the screwdriver in at one end, don’t try it in the middle.

It should pop out without much effort.

Remove the Black Plastic Pictures

2. Enter Service Mode

a. The printer should be plugged in but turned off.

b. Hold Stop/Reset button and Power button for 5 seconds

c. Release Stop/Reset button but continue to hold Power button

d. Press Stop/Reset twice

e. Release the Power Button

f. Wait for Copy any Light to stop blinking before proceeding. (The light differs depending on the model you have.)

g. Press Stop/Reset button twice then Power this will print a simple ROM page. (Make sure the entire page prints before going on to step h.)

h. Press Stop/Reset 5 times then power to select Destination.

i. Press Stop/Reset 4 times then Power to choose Euro.

j. Press Stop/Reset 1 time then power to print a simple ROM again and compare with first ROM print out. (Make sure the entire page prints before going on to step k.)

k. Press Power button Twice to save settings.

3. Install the Driver

The USA driver will work just fine, it is on the CD that came with your printer. If the driver was already installed because you have been using the printer before you found this wonderful page, you will need to UNINSTALL it and RE-INSTALL it.

Advanced Option: How to change the Registry Key

4. Install Software

a. CD Label Print 1.30
b. Nero Cover Designer
c. Acoustica CD Label maker

CD Label Print is OK but some users would prefer other software to create there designs in so I have links to other software such as Nero Cover Designer and Acoustica. If you use Adobe there is a template for it as well: Adobe InDesign template

5. Purchase a Tray

You will need to purchase a tray for the printable cd or dvd to sit on. To know what Tray Letter you need simply look at the properties after you have finished:

Purchase a Canon cd tray on eBay. http://search.ebay.com/

1. Remove plastic blocking the opening.

This can be done very easily with a screw driver. Just lower the door down and slide a flathead screwdriver down behind the plastic piece and very gently push forward.

Be very careful not to damage the soft bendable plastic, might want to wrap the screwdriver in tape first so it doesn’t scrap the plastic either.

I recommend placing the screwdriver in at one end, don’t try it in the middle.

It should pop out without much effort.

2. How to enable the cd print feature:

I. Make sure the printer is off but is plugged in

II. Hold down [RESUME] (Triangle pointed down) and hold down [POWER] and wait 5 seconds or so.

Release [RESUME] but Continue to hold [POWER]. Double click [RESUME]. then Release [POWER].

Check to see you are in service mode by clicking [RESUME], than [POWER]. This should cause the printer to print a simple diagnostic that’ll list it’s ROM number and list CDR SENSOR=OK in red for the last line.

{{{ Note the color of “iPxxx (LTR) V1.xx”. Non-CDR support will be cyan. Keep this sheet to compare to the one after you change the settings. }}}

III. Click the [RESUME] 5 times then click [POWER].This is the Destination setting option.

IV. Click the [RESUME] 5 times “again” and then [POWER]. This is non Japan, CD-R enabled, letter paper mode.

Press [RESUME] then [POWER] again.

{{{ This should cause the same test with ROM information but this time the “iPxxx (LTR) V1.xx” will be pink. }}}

V. To confirm the new settings and return to printing mode press [POWER]. ß { Don’t forget otherwise it will default to JAPAN IPx100}.

3. Install the driver.

The USA driver will work just fine, it is on the CD that came with your printer. If the driver was already installed because you have been using the printer before you found this wonderful page, you will need to UNINSTALL it and RE-INSTALL it.

4. Install Software

a. CDLabelPrint
b. Nero Cover Designer
c. Acoustica CD Label maker

CD Label Print is OK but some users would prefer other software to create there designs in so I have links to other software such as Nero Cover Designer and Acoustica. If you use Adobe there is a template for it as well: Adobe InDesign template

5. Purchase a Tray

You will need to purchase a tray for the printable cd or dvd to sit on. To know what Tray Letter you need simply look at the properties after you have finished:

Search eBay for “Canon cd tray”: http://search.ebay.com/

	Open CD Label Print and select paper type
	click new
	Call it Full DVD and set it for 118mm outside and 22mm inside
	Make sure the size is correct before printing, if you have to measure the media before creating the template.

Technorati : Full hub dvd template for Canon CD label print

Launch CoverDesigner and choose any template, click OK
Click Disk 1 tab at the bottom
Go to the top and click File and the click on Paper Stocks
Highlight User-defined Stocks and click import.
Find the dvd119.dat file.
These measurements are the size of the Canon tray.
Outer radius is 59.250 x 2 = 118.5mm, not exactly 119mm but it’s a good place to start. The goal is to eliminate the white edge but also to keep the overspray to a minimum. You can experiment with the Outer Radius with the media that you have. The Inner Radius of 11mm x 2 = 22mm is also something that may need to be adjusted depending on your media. Click OK to close the Paper Stocks Dialog box.
Now you need to select the new template. Make sure Disc 1 tab is selected.
Finish your Design.
Click Print when you have finished your design. Uncheck Enabled Bleeding box. Click Setup Button.
Select CD-R tray B from the menu. Click the Properties Button.
In properties change Media Type to Printable Disc (recommended). Paper source will automatically change to Disc tray. Put a checkmark next to Preview before printing. Click OK Button then Click OK button again.
Now your back to the Print dialog box. Choose the Elements Tab and unselect everything else but Disk 1. Click OK to begin printing.
If Preview before printing has been selected then this dialog will appear. Your last chance to abort
Warning: This template is for Canon Printers and certain DVD media that is wider then the usual 118mm, the inner radius is set for what is known as full hub DVD that has no stacking ring.

Technorati : 119mm DVD, Canon, Cover designer, Direct printable, Full Hub printable, Nero, Verbatim
Del.icio.us : 119mm DVD, Canon, Cover designer, Direct printable, Full Hub printable, Nero, Verbatim
Ice Rocket : 119mm DVD, Canon, Cover designer, Direct printable, Full Hub printable, Nero, Verbatim
Flickr : 119mm DVD, Canon, Cover designer, Direct printable, Full Hub printable, Nero, Verbatim
Zooomr : 119mm DVD, Canon, Cover designer, Direct printable, Full Hub printable, Nero, Verbatim
Buzznet : 119mm DVD, Canon, Cover designer, Direct printable, Full Hub printable, Nero, Verbatim
Riya : 119mm DVD, Canon, Cover designer, Direct printable, Full Hub printable, Nero, Verbatim
43 Things : 119mm DVD, Canon, Cover designer, Direct printable, Full Hub printable, Nero, Verbatim

1. Remove plastic blocking the opening:

Remove the black plastic blocking the pathway.

2. How to enable the CD printing feature:

I. Make sure the printer is off but is plugged in

II. Hold down [RESUME] (Triangle pointed down) and hold down [POWER] and wait 5 seconds or so.

Release [RESUME] but Continue to hold [POWER]. Double click [RESUME]. then Release [POWER].

Check to see you are in service mode by clicking [RESUME], than [POWER]. This should cause the printer to print a simple diagnostic that’ll list it’s ROM number and list CDR SENSOR=OK in red for the last line.

III. Click the [RESUME] 5 times then click [POWER] . This is the Destination setting option.

IV. Click the [RESUME] 4 times and then [POWER]. This is Europe, CD-R enabled.

Press [RESUME] then [POWER] again.

{{{ This should cause the same test with ROM information but this time: iP4200 EUR V1.04 {in cyan}

V. To confirm the new settings and return to printing mode press [POWER]. (May need to press it twice.)

3. Install the driver:

The USA driver will work just fine, it is on the CD that came with your printer. If the driver was already installed because you have been using the printer before you found this wonderful page, you will need to UNINSTALL it and RE-INSTALL it.

4. Install the CD Label Software:

a. CD Label Print

b. Nero Cover Designer

c. Acoustica CD/DVD Label Maker

5. Purchase or make CD tray:

Search eBay for “Canon cd tray” http://search.ebay.com/