2. Enable CD Print Feature:

I. Make sure the printer is off but is plugged in

II. Hold down [RESUME] (Triangle pointed down) and hold down [POWER] and wait 5 seconds or so.

Release [RESUME] but Continue to hold [POWER]. Double click [RESUME]. then Release [POWER].

Check to see you are in service mode by clicking [RESUME], than [POWER]. This should cause the printer to print a simple diagnostic that’ll list it’s ROM number and list CDR SENSOR=OK in red for the last line.

III. Click the [RESUME] 5 times then click [POWER] . This is the Destination setting option.

IV. Click the [RESUME] 4 times and then [POWER]. This is Europe, CD-R enabled.

Press [RESUME] then [POWER] again.

{{{ This will cause the same test with ROM information but this time: iP4200 EUR V1.04 {in cyan}

V. To confirm the new settings and return to printing mode press [POWER]. ß { Don’t forget otherwise it will default to JAPAN}.

3. Install the driver.

The USA driver will work just fine, it is on the CD that came with your printer. If the driver was already installed because you have been using the printer before you found this wonderful page, you will need to UNINSTALL it and RE-INSTALL it.

4. Install the CD-LabelPrint Software.

Download cd label print

5. Purchase a tray on eBay.

Search ebay for “Canon CD Tray”: http://search.ebay.com/

Technorati : Canon, IP4200, IP5200, Pro9000, cd printing instructions

Expand To Read the Full Article

1. Remove the black plastic

This can be done very easily with a screw driver. Just lower the door down and slide a flathead screwdriver down behind the plastic piece and very gently push forward.

Be very careful not to damage the soft bendable plastic, might want to wrap the screwdriver in tape first so it doesn’t scrap the plastic either.

I recommend placing the screwdriver in at one end, don’t try it in the middle.

It should pop out without much effort.

Remove the Black Plastic Pictures

2. Enter Service Mode

a. The printer should be plugged in but turned off.

b. Hold Stop/Reset button and Power button for 5 seconds

c. Release Stop/Reset button but continue to hold Power button

d. Press Stop/Reset twice

e. Release the Power Button

f. Wait for Copy any Light to stop blinking before proceeding. (The light differs depending on the model you have.)

g. Press Stop/Reset button 1 time then Power this will print a service print out.

h. Press Stop/Reset 5 times then power to select Destination.

i. Press Stop/Reset 4 times then Power to choose Euro.

j. Press Stop/Reset 1 time then Power to print a service print out again.

k. Press Power button Twice to save settings.

3. Install the Driver

The USA driver will work just fine, it is on the CD that came with your printer. If the driver was already installed because you have been using the printer before you found this wonderful page, you will need to UNINSTALL it and RE-INSTALL it.

Advanced Option: How to change the Registry Key

4. Install Software

a. CD Label Print 1.30
b. Nero Cover Designer
c. Acoustica CD Label maker

CD Label Print is OK but some users would prefer other software to create there designs in so I have links to other software such as Nero Cover Designer and Acoustica. If you use Adobe there is a template for it as well: Adobe InDesign template

5. Purchase a Tray

You will need to purchase a tray for the printable cd or dvd to sit on. To know what Tray Letter you need simply look at the properties after you have finished:

Purchase a Canon cd tray on eBay. http://search.ebay.com/

Expand To Read the Full Article

1. Remove plastic blocking the opening.

This can be done very easily with a screw driver. Just lower the door down and slide a flathead screwdriver down behind the plastic piece and very gently push forward.

Be very careful not to damage the soft bendable plastic, might want to wrap the screwdriver in tape first so it doesn’t scrap the plastic either.

I recommend placing the screwdriver in at one end, don’t try it in the middle.

It should pop out without much effort.

2. How to enable the cd print feature:

I. Make sure the printer is off but is plugged in

II. Hold down [RESUME] (Triangle pointed down) and hold down [POWER] and wait 5 seconds or so.

Release [RESUME] but Continue to hold [POWER]. Double click [RESUME]. then Release [POWER].

Check to see you are in service mode by clicking [RESUME], than [POWER]. This should cause the printer to print a simple diagnostic that’ll list it’s ROM number and list CDR SENSOR=OK in red for the last line.

{{{ Note the color of “iPxxx (LTR) V1.xx”. Non-CDR support will be cyan. Keep this sheet to compare to the one after you change the settings. }}}

III. Click the [RESUME] 5 times then click [POWER].This is the Destination setting option.

IV. Click the [RESUME] 5 times “again” and then [POWER]. This is non Japan, CD-R enabled, letter paper mode.

Press [RESUME] then [POWER] again.

{{{ This should cause the same test with ROM information but this time the “iPxxx (LTR) V1.xx” will be pink. }}}

V. To confirm the new settings and return to printing mode press [POWER]. { Don’t forget otherwise it will default to JAPAN IPx100}.

3. Install the driver.

The USA driver will work just fine, it is on the CD that came with your printer. If the driver was already installed because you have been using the printer before you found this wonderful page, you will need to UNINSTALL it and RE-INSTALL it.

4. Install Software

a. CDLabelPrint
b. Nero Cover Designer
c. Acoustica CD Label maker

CD Label Print is OK but some users would prefer other software to create there designs in so I have links to other software such as Nero Cover Designer and Acoustica. If you use Adobe there is a template for it as well: Adobe InDesign template

5. Purchase a Tray

You will need to purchase a tray for the printable cd or dvd to sit on. To know what Tray Letter you need simply look at the properties after you have finished:

Search eBay for “Canon cd tray”: http://search.ebay.com/

Expand To Read the Full Article

1. Remove plastic blocking the opening:

Remove the black plastic blocking the pathway.

2. How to enable the CD printing feature:

I. Make sure the printer is off but is plugged in

II. Hold down [RESUME] (Triangle pointed down) and hold down [POWER] and wait 5 seconds or so.

Release [RESUME] but Continue to hold [POWER]. Double click [RESUME]. then Release [POWER].

Check to see you are in service mode by clicking [RESUME], than [POWER]. This should cause the printer to print a simple diagnostic that’ll list it’s ROM number and list CDR SENSOR=OK in red for the last line.

III. Click the [RESUME] 5 times then click [POWER] . This is the Destination setting option.

IV. Click the [RESUME] 4 times and then [POWER]. This is Europe, CD-R enabled.

Press [RESUME] then [POWER] again.

{{{ This should cause the same test with ROM information but this time: iP4200 EUR V1.04 {in cyan}

V. To confirm the new settings and return to printing mode press [POWER]. (May need to press it twice.)

3. Install the driver:

The USA driver will work just fine, it is on the CD that came with your printer. If the driver was already installed because you have been using the printer before you found this wonderful page, you will need to UNINSTALL it and RE-INSTALL it.

4. Install the CD Label Software:

a. CD Label Print

b. Nero Cover Designer

c. Acoustica CD/DVD Label Maker

5. Purchase or make CD tray:

Search eBay for “Canon cd tray” http://search.ebay.com/

Expand To Read the Full Article