74 Responses to “*New* CD Print enabler for iP4820, MG5220, MG6120, MG8120”

1. Paul Permalink Feb 9th, 2011 11:23 am

   1 The new program seemed to work, but I have tray “G” for the MG8120 and it will take the tray in and act like it’s printing but not print. Is there a way to tell which tray may be needed? The tray is the correct width, but I’m guessing the reflector points are in the wrong places. life2extremes@yahoo.com Quote Comment{Quotes will added to the form below}Jump to Form

2. Paul Permalink Feb 9th, 2011 7:04 pm

   2 Update: I tried several countries and the CDRS remains =(0000) Quote Comment{Quotes will added to the form below}Jump to Form

3. QuadCore Permalink Feb 9th, 2011 8:51 pm

   3 Administrator Comment Hey Paul: Try repeating step 3a ten times before going on to step 3b. Also tray types do matter and can result in tray rejection. The tray letter will be stated in the printer properties under page setup and then page size drop down menu. Quote Comment{Quotes will added to the form below}Jump to Form

4. Paul Permalink Feb 9th, 2011 11:23 pm

   4 I have verified it’s supposed to be tray “G”, which is the one I got for a dead printer. After 2 times of selecting EUR and SET, the program closes. I tried a total of 10 times and still have all zeroes for CDR, CDRP and CDRS. The top of the printout does list EUR V1.020 as it had before. After setting Service mode, and performing the above steps, I turned off the printer, wait a min, then turn it back on. It will feed a blank sheet, then continue with the power on cycle. Disk Label print shows up under the “fun photo print” menu. Is there a better test program than the Canon CD print utility? I have tried both the utility and printing a picture off a CF card inserted into the printer, and it will roll the disk in, spit it back out and display printing, then show an error: there is no disk tray. set the tray and press OK. I have an i960 also if you could direct me to the page showing what part needs to be removed/replaced with the “roller kit” Thank You. Quote Comment{Quotes will added to the form below}Jump to Form

5. Paul Permalink Feb 10th, 2011 9:05 am

   5 Test 1, now shows CDRS=(0233) , test 2 shows CDR Sensor= OK and it now prints to CD. Thank You Quote Comment{Quotes will added to the form below}Jump to Form

6. tbird2340 Permalink Feb 13th, 2011 7:34 am

   6 I have a MG5220.. Even if I get this print mode enabled how do you print CDs? There is no tray that I can find to buy for it.. Thanks Quote Comment{Quotes will added to the form below}Jump to Form

7. Jason Permalink Feb 13th, 2011 4:44 pm

   7 I tried it on my MG6120, it worked great, only to two try’s and everything is great. Thanks so much. Quote Comment{Quotes will added to the form below}Jump to Form

8. QuadCore Permalink Feb 14th, 2011 2:00 am

   8 Administrator Comment I believe it’s tray g, it will be listed in the printer properties so you will know the right tray to buy. Quote Comment{Quotes will added to the form below}Jump to Form

9. kunal Permalink Feb 14th, 2011 12:40 pm

   9 Hey, Can anyone confirm that this will work in MG6120 bought in North America? If not, is there any way to have instructions to enable it in USA? Appreciate all the help, thanks. Quote Comment{Quotes will added to the form below}Jump to Form

10. tbird2340 Permalink Feb 14th, 2011 2:43 pm

    10 Ok just a few more questions before I give this a go.. 1. So I need my PC hooked up via USB to the printer to do this (I’m assuming yes but just want clarification). 2. This modifies the printer firmware? 2a. If so, I think I read this also voids the warranty? So I just got my printer not even a week ago and if I do this and the printer somehow fails a month from now I can’t get it replaced under warranty? There is no way to flash back? 3. I have a MG5220… So for sure there is a tray that will work with this? (QuadCore believes it will be Tray G)? On Ebay Tray G does not list to be compatible with the 5220.. I’m guessing maybe just because this mod for this model is new? 4. Step 1 says to remove black plastic and that it has no pictures and wants them emailed to that address.. I’d be happy to do this if I knew what to take a picture of.. Thanks! Quote Comment{Quotes will added to the form below}Jump to Form

11. tbird2340 Permalink Feb 14th, 2011 7:08 pm

    11 OK just tried this with my MG5220.. Turned printer off, held down Stop button, then held down power button while continuing to hold down Stop button.. Counted to 5 and then released stop button.. While holding in power button I pressed the stop button twice (the first time the amber light lit up, the second time the green light lit up), I then let go of the power button.. Printer looked like it as powered on normally.. I then tried to “Set” to EUR and got a “Error code: 005″.. Hoping someone may have some pointers. Quote Comment{Quotes will added to the form below}Jump to Form

12. QuadCore Permalink Feb 14th, 2011 8:55 pm

    12 Administrator Comment Kunal: This is for North American Canon models. Quote Comment{Quotes will added to the form below}Jump to Form

13. QuadCore Permalink Feb 14th, 2011 8:58 pm

    13 Administrator Comment tbird2340: Try the second set of Instructions since your using a MG series. Also note whether you have a scanner on your model. Quote Comment{Quotes will added to the form below}Jump to Form

14. kunal Permalink Feb 14th, 2011 10:40 pm

    14 Thanks a lot, will try this on friday and confirm if it works or not for me. Quote Comment{Quotes will added to the form below}Jump to Form

15. tbird2340 Permalink Feb 14th, 2011 11:57 pm

    15 Yes, my MG5220 has a scanner. I tried these: a. Press and hold the ON button. b. When the Power light is steady, press the OK button to light up the panel. c. Press the Stop button 5 or 6* times. d. Release the On button. e. When the Power light is steady, the machine is ready. And when I do steps A & B the panel never lights up.. Quote Comment{Quotes will added to the form below}Jump to Form

16. QuadCore Permalink Feb 15th, 2011 2:54 am

    16 Administrator Comment tbird2340: Try this then: a. Press and hold the ON button. c. Press the Stop button 5 or 6* times. d. Release the On button. e. When the Power light is steady, the machine is ready. Let me know… Quote Comment{Quotes will added to the form below}Jump to Form

17. tbird2340 Permalink Feb 15th, 2011 6:30 am

    17 I tried doing that both the 5 times and the 6 times and each time got error code 006. Quote Comment{Quotes will added to the form below}Jump to Form

18. QuadCore Permalink Feb 15th, 2011 9:20 am

    18 Administrator Comment tbird2340: It didn’t work then. Also to answer your early question the 5220 doesn’t have the touch display like the 8120 so it won’t light up and that step isn’t necessary. Quote Comment{Quotes will added to the form below}Jump to Form

19. tbird2340 Permalink Feb 15th, 2011 12:23 pm

    19 Just curious.. Why won’t it work if it *should* work? I REALLY want this feature! Thanks much. Quote Comment{Quotes will added to the form below}Jump to Form

20. Paul Permalink Feb 15th, 2011 10:29 pm

    20 I have the MG8120 and it NEEDS to be connected via USB and have the drivers installed. It cannot connect vis Ethernet (and I’m assuming the same with WiFi) Quote Comment{Quotes will added to the form below}Jump to Form

21. QuadCore Permalink Feb 16th, 2011 10:44 am

    21 Administrator Comment Paul: USB port only…..never tried it with wifi. Quote Comment{Quotes will added to the form below}Jump to Form

22. PN Permalink Feb 16th, 2011 8:43 pm

    22 Confirmed that this is working for the iP4820. Print 1 test shows CDRS=(0073) and printer properties shows CD Tray G. I don’t have tray G, but the printer did attempt to print. Quote Comment{Quotes will added to the form below}Jump to Form

23. Joe Permalink Feb 17th, 2011 1:03 am

    23 I just tried this on my new MG6120 & The CDRS say 0140. And the Rom Says EUR 1.30. So i think this did work. However it took me several tries to get the cdrs to change form 0000, more then 10 times but it finally did after i changed it back USA & t hen to EUR. Quote Comment{Quotes will added to the form below}Jump to Form

24. PhatPhreddy Permalink Feb 17th, 2011 10:40 am

    24 This worked great on a new MG6120! Even though this model has a scanner, it requires pressing the Stop button 6 times not 5 in order to enter Service Mode as described in direction set b. Tray G is required. Set up must be done via USB but once accomplished, the printer can be used as a network printer. Quote Comment{Quotes will added to the form below}Jump to Form

25. PN Permalink Feb 17th, 2011 6:35 pm

    25 iP4820 seems like it could work. I was able to get CDRS=(0074) using the above instructions. Print driver allows me to choose CD Tray G. Quote Comment{Quotes will added to the form below}Jump to Form

26. kunal Permalink Feb 18th, 2011 6:08 pm

    26 I was able to get EUR, CDRS = (0085) AND CDR Sensor = ok on a new MG6120….i don’t know what to do after getting all these things done. I uninstalled and reinstalled the drivers, installed the cd-print too…but whenever i try to print a disc…it says the inner door is open, please close. Can anyone help me here plz. Thanks. Quote Comment{Quotes will added to the form below}Jump to Form

27. vcasm Permalink Feb 18th, 2011 6:29 pm

    27 Appears to have worked with MG5220 using the first service mode instructions except pressing stop button 6 times (to change light from amber to green). Still need to get a G tray to verify it is working properly. Took a few tries before CD-Labelprint would acknowledge the printer. Quote Comment{Quotes will added to the form below}Jump to Form

28. Kunal Permalink Feb 18th, 2011 7:14 pm

    28 Disregard my previous comment about what to do next after getting everything right. I can confirm that step B works for my MG6120 and have to press the Stop button 6 times to get it in service Mode. When trying to put the printer in service mode – keep the inner cd door closed. Cd-label print worked for me after i removed HP 1018 and Canon MP560 from the computer and i was successfully able to print on the disc Thanks a lot for these instructions. I will soon send you the printouts and cd printed image as a proof to your gmail. Quote Comment{Quotes will added to the form below}Jump to Form

29. D Harvey Permalink Feb 19th, 2011 5:58 pm

    29 If you buy these printers in Canada they come with the DVD trays included.I bought the MG5220 and it comes with the G tray.Below where “Canon” is printed there is a slot which you push down on and a module which accepts the DVD tray drops into place. Quote Comment{Quotes will added to the form below}Jump to Form

30. D Harvey Permalink Feb 19th, 2011 7:38 pm

    30 Why did you only press the stop button 2 times when the instructions say to press it 5 times?When I do this on my MG5220 the LCD goes blank and a “found new hardware” wizard pops up in Windows.Maybe yours will behave differently because mine was purchased in Canada so DVD printing has been already enabled. Quote Comment{Quotes will added to the form below}Jump to Form

31. Joe Permalink Feb 19th, 2011 11:06 pm

    31 i will confirm that this works as soon as i get my tray G in the mail. I should get it on Monday i am hoping. When i try to print to a cd right now it says to open the inner door & slide the tray in. SO i am assuming ti will work as soon as i get they try G & official print on a cd. Quote Comment{Quotes will added to the form below}Jump to Form

32. QuadCore Permalink Feb 20th, 2011 3:40 am

    32 Administrator Comment Good to hear. Quote Comment{Quotes will added to the form below}Jump to Form

33. Jerry Permalink Mar 5th, 2011 7:33 pm

    33 I have the MG8120. I followed the instructions and have successfully activated the CD tray. Once the drivers were reinstalled, the “tray G” printer drawer appeared in the printer tray drop dow. I am now waiting for the disc tray to arrive. It should arrive sometime next week. I will update at that time if I can print a label. Quote Comment{Quotes will added to the form below}Jump to Form

34. Joe Permalink Mar 6th, 2011 2:08 am

    34 I just want to confirm that the enabler did work 100% perfectly on my MG6120. I haven been printing on cds for about 2 weeks now! Quote Comment{Quotes will added to the form below}Jump to Form

35. Bob Permalink Mar 6th, 2011 12:05 pm

    35 One quick note about the MG6120. It will not work if you have your printer set up as wifi. You must use the usb cable to run cd-print tool as the printer does not communicate wifi when in service mode. At least that is my experience. Quote Comment{Quotes will added to the form below}Jump to Form

36. Jerry Permalink Mar 9th, 2011 3:47 pm

    36 I received my “G” CD tray today. I can confirm I am printing CDs on my MG8120 successfully. Works like a charm. One side note. Do not insert the CD tray until the printer asks for it..otherwise it will eject it. Quote Comment{Quotes will added to the form below}Jump to Form

37. Bill Permalink Mar 10th, 2011 4:17 pm

    37 Confirmed Working on my ip4820 following instructions above. CDRS=68. Reinstalled the drivers and tested with SureThing CD/DVD Labeler v5.2.663 Works on Tray G! If you have the XPS 16-bpc drivers installed you have to make sure to uninstall both the XPS and Basic Driver before reinstalling. Quote Comment{Quotes will added to the form below}Jump to Form

38. CKNoblet Permalink Mar 16th, 2011 10:15 pm

    38 Confirmed working with MG5220 USA version, purchased at Best Buy. This printer uses PRINTER TRAY G, which can be purchased from eBay for about $25.00. Like the above mentioned 5220 posts, I had to hit the Resume button 6 times. When the printer is in service mode, the LCD goes blank. After going through the directions listed at the top of this post, I uninstalled my current USA driver, went to Canon Europe and downloaded the MP driver for the 5240 printer. Apparently there’s no Europe version labled as 5220. Nontheless the 5240 driver gives you a 5200 family driver which works just fine. Here is a link to the driver I’m using: http://files.canon-europe.com/files/soft39930/software/mg5200swin104ea24.exe I don’t like Canon’s cd printer software, so I used the free UnderCover XP disc printing software. Simple and free. When printing, make sure you set the CD print program and Print Properties to use PIXMA Tray G for the printout. The first time you print a disc, it literally clicks and clacks for 5 minutes with a “please wait” sorta message while it’s working away. The next time you print a disc though, it’s pretty much instantly ready to go. Thanks again Damn Printer! CKNoblet Quote Comment{Quotes will added to the form below}Jump to Form

39. Dave F Permalink Mar 20th, 2011 11:15 pm

    39 I’m trying to crack the MG6120 and I’m on a Mac. Is there any other way besides downloading enterprise trial to get the CD-Print Tool to work? Quote Comment{Quotes will added to the form below}Jump to Form

40. QuadCore Permalink Mar 21st, 2011 7:35 am

    40 Administrator Comment Hello Dave F 1. Borrow Laptop running Windows. 2. Bring printer someplace that has a Windows Desktop. It only needs to be accomplished once. It is Windows only since they exist everywhere (except your house). Quote Comment{Quotes will added to the form below}Jump to Form

41. Bryan Permalink Mar 22nd, 2011 1:01 am

    41 Jerry, can you PLEASE tell me whether you pushed STOP 5 times or 6? The instructions say 6 times for the 6120, but for the 8120 it’s just blank! Thanks very much. Quote Comment{Quotes will added to the form below}Jump to Form

42. Butcher0 Permalink Mar 22nd, 2011 7:19 am

    42 Here are the exact steps that worked for me in order to use the USA purchased Canon iP4820 as a CD/DVD Printer. The printer arrived in its box and I unpacked and assembled it, closely following the enclosed, detailed instructions. It worked just fine, as had my iP4000 and iP4200. The iP400 was destroyed in an unfortunate accident and the iP4200′s power supply ceased functioning – much to my disappointment. I, then, ordered the print tray “G” from an EBay merchant, Aiguangfei, based in Shenzhen, Guangdong, China. The reasonably priced, including shipping, tray arrived surprisingly well protected about twenty days later. I had, already and surprisingly easily, removed the black plastic piece from the printer. Note that the pictures on the web site are perfectly fine, since there has been little change in the physical layout of the external implementation of the CD/DVD print mechanism for Canon. Here are the exact steps used to successfully print my first iP4820-printed DVD: as follows: • The iP4820 is fully installed, plugged-in and working just fine, although turned off. • Hold down the resume button (just below the power button) and press and hold down the power button, as well. The power light will come on. • Continue to hold both buttons down for at least five seconds, then release only the resume button and press it five times, slowly and affirmatively. • Now, release both buttons. • When the green power LED lights steadily, the printer is in service mode operation. • Start the CD-Print-Tool v7. From the drop down menu, select EUR, then press the SET button. IGNORE the computer’s demand to install drivers for a new device. Carefully listen for the printer to stop its mysterious noises and repeat, being sure to re-select EUR, again. The CD-Print-Tool v7 will probably close, after affirming the operation was accomplished. • Start the CD-Print-Tool v7, again, repeating the EUR and SET button, one more time. Listen for the printer to stop making noises. Then, press the CD-Print-Tool v7 PRINT button. My printout showed EUR v 1.020 at the top and CDRS= (0133) at the middle page left. • I, then, uninstalled the iP4820 printer driver in the “Printers” section of the OS menu. • I powered down the iP4820 and unplugged the USB cable. • I inserted the Canon US installation CD into the computer CD/DVD mechanism and proceeded to re-install all the software and drivers on the disk, plugging the printer’s USB cable when prompted. Several minutes later the installation of the software and drivers were completed. • I put a blank ink-jet-printable CD/DVD into the “G” tray, opened the Canon CD-Label Print v1.41 software program, loaded an image to print, centered and expanded the image and pressed PRINT. The Canon print driver software warned me not to insert the CD/DVD, of course, while taking what seemed like forever to recalibrate itself to print the disk. It, then, commanded me to pull down the inner door and insert the CD/DVD tray (matching the two arrows on the tray and the printer inner door I had just opened). It instructed me to press the RESUME button, which I did. The iP4820 proceeded to print out a perfectly beautiful DVD. Hooray, I am in bidness, again. I hope that the installation and usage of your Canon printer goes as successfully and as easily as mine. However, since the Canon cost-to-print is so exorbitant, compared to most other brands, my next step is to replace the, now black and non-translucent cartridges with translucent, see-through, top-fill replacement cartridges. Of course, I will transfer the Canon cartridge chips onto the “new” refillable foam-free cartridges; fill them with quality “bulk” ink and slash my per-print cost absolutely dramatically, waiting patiently for the (hopefully) soon-to-arrive chip re-setter. I, also, strongly suggest the usage of the freeware paint.NET software as a great program to edit and/or make the CD/DVD graphics. It is powerful, easy to us and best of all, FREE! …Note that I am not affiliated, in any way with Canon, paint.NET, the tray supplier, cartridge supplier, bulk ink supplier, or etc… Quote Comment{Quotes will added to the form below}Jump to Form

43. QuadCore Permalink Mar 22nd, 2011 1:23 pm

    43 Administrator Comment Bryan: 6 times….just updated the instructions a bit. Quote Comment{Quotes will added to the form below}Jump to Form

44. Jerry Permalink Mar 23rd, 2011 6:30 pm

    44 Bryan, I did it six times. Once you complete the process and you get your print outs. If all your result areas don’t have the good values, repeat the entire process again. I had to go through it twice before all the values changed. Quote Comment{Quotes will added to the form below}Jump to Form

45. tbird2340 Permalink Mar 24th, 2011 7:51 pm

    45 I have a MG5220.. I got the EUR enabled but not sure what plastic piece I need to remove.. Can someone offer some guidance? Thanks Quote Comment{Quotes will added to the form below}Jump to Form

46. James Permalink Apr 1st, 2011 8:22 pm

    46 Hope you guys can help me out. I previously had a ip4200 with CD printing enabled. I am trying to hack my IP4820 per instructions above but to no avail. I am pretty sure I am getting into service mode because the green light flashes for a bit and then goes solid, and I am not getting the error code 6 when running the CD print tool. Every time I print the test page it says CDRS=0000. That’s a no-go, right? The instructions here are a little vague as to whether I am supposed to click the set button 10 times or open the program 10 times and click each time til it closes (after the third time). I tried both ways to no avail. Any help appreciated. Quote Comment{Quotes will added to the form below}Jump to Form

47. QuadCore Permalink Apr 6th, 2011 7:13 am

    47 Administrator Comment James: Sorry about the vagueness, I was in a hurry to get the new models updated. You were suppose to press the set button and then wait for the OK and then press the set button again. Sometimes the cd-print-tool will crash after the 2 or 3rd time though. Try this: 1. Enter Service Mode 2. Euro then Set (wait for confirmation) 3. Print 2 button (Three sheets will print) 4. Euro then Set (wait for confirmation) 5. Print 1 button Quote Comment{Quotes will added to the form below}Jump to Form

48. Jeffrey Permalink Apr 11th, 2011 12:53 pm

    48 I have the MG6120, I can get it into EUR mode, however I’m not able to get the CDRS off 0000. I have tried about everything I could think of, I tried going back to USA mode and back to EUR then running the print tool software about 20 times. I’ve tried going to AUS mode and back to EUR. Nothing I’m doing seems to work. Is it normal for this printer to take several minutes to switch modes? Like going from copy mode to printing from PC mode it takes forever to get itself situated, I can’t believe this is normal. Please Help, Thanks, Jeffrey Quote Comment{Quotes will added to the form below}Jump to Form

49. QuadCore Permalink Apr 16th, 2011 2:48 pm

    49 Administrator Comment Jeffrey: Sometimes the cdrs will land on zero’s and it will be enabled. Kinda rare. Did you print out the sheets? The printer can be slow to get going, does it make a bunch of mechanical sounds? Quote Comment{Quotes will added to the form below}Jump to Form

50. Dave F Permalink Apr 19th, 2011 11:02 pm

    50 I’m trying to crack my MG6120. What did your CDRS= say? Quote Comment{Quotes will added to the form below}Jump to Form

51. Dave F Permalink Apr 19th, 2011 11:02 pm

    51 I’m trying to crack my MG6120. What did your CDRS= say? Quote Comment{Quotes will added to the form below}Jump to Form

52. Dave F Permalink Apr 19th, 2011 11:31 pm

    52 Trying to crack the MG6120 on a Mac. I got a PC laptop to use the CD Printool. I keep getting between CDRS=84,86,87. Then I switch to my mac to try to print using ‘Label Print’ The printer does not flip out when I lower the tray to put the cd tray in. But when I try to print it takes in the tray, makes some noise and then slowly spits out the try and the printer just says processing and does not do anything. Am I missing something? Quote Comment{Quotes will added to the form below}Jump to Form

53. QuadCore Permalink Apr 20th, 2011 9:26 am

    53 Administrator Comment Dave F. 1. Don’t lower the inner door or put the tray in until the *software* tells you, otherwise you will get an error. 2. Make sure that mac print driver is up to date. (You didn’t say what version of OSX you were using.) 3. Verify that it works on your PC laptop first. Macs can be problematic with this feature. 4. The CDRS numbers sound fine, no need to repeat that part. Quote Comment{Quotes will added to the form below}Jump to Form

54. Dave F Permalink Apr 25th, 2011 8:09 pm

    54 I running OSX 10.6.7 Quote Comment{Quotes will added to the form below}Jump to Form

55. Kev Permalink May 12th, 2011 7:28 pm

    55 Running the Pixma 5220 on Windows. I have tried several times downloding the Cd-Print Tool v7 but whenever I launch it, the options boxes are greyed out so I can’t select EUR. Anyone else hd this and resolved the issue? Quote Comment{Quotes will added to the form below}Jump to Form

56. D.W. Palme Permalink May 16th, 2011 5:59 pm

    56 I have an IP4820 and following the steps on parallels (Mac windows side) I only get two pages printed the first time, one says CDR sensor is oi and the other is the color code bars, it shows a CDRS of 0069 and 0068 from two separate tests….. on printing the print 1 it comes up with CDRS 0000. I am assuming this is failing, but I am not sure why. Any help or suggestions would be appreciated. I installed the drivers first so that it would be found on the windows side, I then held down the resume and power buttons for five seconds (one thousand one, one thousand two, etc.) and then released the resume button, then pushed the resume button five times and let go of the power, after blinking for a bit it goes solid green, so I thought I was in service mode but what I got was the results from above. Quote Comment{Quotes will added to the form below}Jump to Form

57. QuadCore Permalink May 16th, 2011 10:36 pm

    57 Administrator Comment D.W. Palme: You can stop after getting the CDRS numbers the first time. Two sheets is OK. Print 1 is only for models that are not successful with Print 2. Confirm success or failure by continue the rest of the instructions. Check the printer properties for Printable disc and Tray G in the drop down menu’s after reinstalling the print driver. Quote Comment{Quotes will added to the form below}Jump to Form

58. QuadCore Permalink May 16th, 2011 10:40 pm

    58 Administrator Comment Kev: I just downloaded it and it works fine under Windows 7 64-bit. Quote Comment{Quotes will added to the form below}Jump to Form

59. zeeshan Permalink May 29th, 2011 5:38 am

    59 hi i have canon ip4840 printer.the problem is my printer rejects the cd tray i used new version of cd enabler but its dont work.print paper shows EUR V 1.020 on the top of the paper and in the middle of the paper CDRP =(-0576, -0240) and CDRS =(0077) second page also showing same things but 3rd page shows CD SENSOR = NG. please help me how to fix this problem. Quote Comment{Quotes will added to the form below}Jump to Form

60. QuadCore Permalink May 29th, 2011 6:27 am

    60 Administrator Comment Zeeshan: It’s non-functioning, fails it’s own test. If this is a newly purchased printer I would exchange it for another. Quote Comment{Quotes will added to the form below}Jump to Form

61. marito79 Permalink Jun 11th, 2011 3:30 am

    61 I can not use the CD-Print-Tool v7 to run it gives me error 006 please Quote Comment{Quotes will added to the form below}Jump to Form

62. QuadCore Permalink Jun 19th, 2011 6:35 am

    62 Administrator Comment marito: error code 006 means no connection. You did put the printer in service mode first right? Quote Comment{Quotes will added to the form below}Jump to Form

63. Hector Permalink Jul 12th, 2011 2:21 pm

    63 ITS WORK.I’ve a Canon MG5220 and I’m running Windows 7 64bit Here is How I done it. 1.Download driver from Canon UK website. a.Uninstall your current driver and install the one you downloaded from Canon UK website select (Europe, Middle East, Africa) 2.Hold the STOP button a.Keep holding the STOP button and now hold down the POWER button as well. b.After 5 seconds of holding both buttons let go of the STOP button but keep holding the POWER button. c. Press the STOP button 6 times and then let go of the POWER button. d.The Power LED lights is blinking for a few times and the panel is black , the printer is ready for the service mode operation and the CD-Print Tool 3.Launch the CD-Print-Tool v7 a. Select EUR from drop down and press SET. Wait for it to finish. for a short while you’ll here the the printer is clicking [(Do all likes that) Click And Wait be patient]. b. Select EUR from drop down and press SET. Wait for it to finish. c. Select EUR from drop down and press SET. Wait for it to finish. d. Press the Print 2 button. Print 2 may not work with your model…move on to step e. (Two sheets will print) e. Select EUR from drop down and press SET. Wait for it to finish. f. Press the Print 1 button. Select Rear Tray and print the sheet to confirm changes. (One sheet will print) The CD Print Enabler may crash, just re-launch it 4. Reinstall the driver: Changes to the printer have been made but won’t show up in the printer properties until the driver is uninstalled and reinstalled. a.Uninstall the driver and shutdown the printer b.Turn it back on (Windows should install the driver for you) if not just install the one you download from Canon UK web. Printing CD/DVD Lunch CD Label Print 1.42 (download from the above links) Do your design and hit print the message will appear tell you to wait (this is a long waiting time ever) after its done it will tell you what to do That’s ALL. Thank you QuadCore for your instructions. Quote Comment{Quotes will added to the form below}Jump to Form

64. Faisal Khatib Permalink Jul 20th, 2011 12:30 pm

    64 Does anyone know if there is a way to make the Pixma 8120 compatible to the CLI 426 cartridges? Basically the CLI 426 is the Asian version of the CLI 226 and is compatible with the Pixma 8140 Quote Comment{Quotes will added to the form below}Jump to Form

65. Becky Permalink Jul 22nd, 2011 9:23 am

    65 I have the MG8120. When I go through the steps, the CD print tool v7 never comes up – there is just a blank screen on the printer. Can you guess what I am doing wrong? Also then to uninstall and reinstall the driver – do I use the original CD that came with the Canon printer? Am I supposed to have it in my computer all along? I use Windows 7. Quote Comment{Quotes will added to the form below}Jump to Form

66. jf Permalink Jul 24th, 2011 9:12 pm

    66 Hi. The MG6120 in Canada is the same thing from USA? The Tray is not come with it? Thanks for your time. Quote Comment{Quotes will added to the form below}Jump to Form

67. Jonathan Permalink Jul 29th, 2011 3:45 pm

    67 (Sorry if this isn’t the right place to put this, but I didn’t see any better option.) I’ve seen comments in this thread and others that say things like “…mine was purchased in Canada so DVD printing has been already enabled” and “…If you buy these printers in Canada they come with the DVD trays included.” I am totally perplexed by this. I’ve checked Canon’s Canada site thoroughly, and nowhere in the specifications of any of the printer models being discussed here is there any mention of CD printing. In other words, it very much seems as though CD printing is disabled/not supported on Canadian-sold models just as it is with USA-sold models. Are they seriously selling printers with CD printing capabilities in Canada and simply not telling anyone??? Quote Comment{Quotes will added to the form below}Jump to Form

68. QuadCore Permalink Aug 1st, 2011 3:03 am

    68 Administrator Comment Becky: The LCD on the printer is NOT used during the process. Just put the printer in service mode and the launch the CD print enabler, follow the rest of the instructions. The driver re-install is the last thing required. Quote Comment{Quotes will added to the form below}Jump to Form

69. QuadCore Permalink Aug 1st, 2011 3:25 am

    69 Administrator Comment Jonathan: For awhile Canadian printers came with the tray and were enabled. They may have changed their policy. Quote Comment{Quotes will added to the form below}Jump to Form

70. QuadCore Permalink Aug 1st, 2011 3:28 am

    70 Administrator Comment JF: They are probably the same, the tray may no longer be included. Canon Canada may have changed their policy. Quote Comment{Quotes will added to the form below}Jump to Form

71. QuadCore Permalink Aug 1st, 2011 3:29 am

    71 Administrator Comment Faisal Khatib: Their are more then likely physical differences or programming differences that keep the carts from being interchangeable. Quote Comment{Quotes will added to the form below}Jump to Form

72. tina Permalink Sep 3rd, 2011 6:07 pm

    72 Has anyone had a problem with the computer not seeing the connection with the printer? I have a new iP4820 and I followed all of the steps on this site to convert it to be able to print on CDs. It printed fine before I started and now I can’t get it to recognize the printer. Quote Comment{Quotes will added to the form below}Jump to Form

73. tina Permalink Sep 3rd, 2011 6:34 pm

    73 ok, I figured that part out. My computer was trying to print to the old printer. Changed all those settings and it’s printing now. So, the problem that I have now is even though I am choosing the Tray G to print from it’s still trying to print from the rear tray. If I put the G tray in the slot it tells me it can’t print with the front cover open. Quote Comment{Quotes will added to the form below}Jump to Form

74. XploRa Permalink Dec 27th, 2011 2:33 am

    74 Hi, Is the MG5240 the same printer as the MG 5220 ? Quote Comment{Quotes will added to the form below}Jump to Form

Main RSS
Hot Deals RSS
Tray Rejection RSS
Comments RSS

________________

________________

• Other
  • No categories

All Instructions:

• 02/08/2011::*New* CD Print enabler for iP4820, MG5220, MG6120, MG8120(74)
• 01/25/2010::CD Printing Enabler for iP4700, MP640, MP990, PRO9000 MK II, PRO9500 MK II(121)
• 11/17/2008::LCD appears in Japanese suddenly instead of english?(0)
• 11/17/2008::New Canon printers have less ink(1)
• 06/24/2008::Refill instructions for Canon PG-40, PG-50 and CL-41 and CL-51(1)
• 04/23/2008::EEPROM & Service Mode Printout(8)
• 12/09/2007::*The Five Easy Steps*(124)
• 11/11/2007::Canon CD print alignment(39)
• 09/18/2007::Canon Operator Call Errors(1)
• 09/18/2007::Canon Service Call Errors(137)



Tray Rejection:

• 08/27/2007::Tray Rejection and Mac OS X(19)
• 08/21/2007::Tray Rejection General Guide(40)
• 05/09/2007::CD LabelPrint and OSX(1)



Templates:

• 03/02/2008::Print Direct Photoshop Template(18)
• 12/20/2007::Print Direct InDesign Template(3)
• 04/06/2007::Easy Adobe Photoshop cd label(0)
• 11/05/2006::Nero Cover Designer 119mm template for Tray F(21)
• 10/24/2006::CD Label Print: Full hub Template(9)
• 10/24/2006::Nero Cover Designer 119mm template for Tray B(2)
• 09/05/2006::Print Direct Adobe Illustrator Template(2)


© 2007 Damn Printer. All Rights Reserved.

Recent Comments:

• ray.z: Hi, I have a Pro9000 Mark II USA model. I have tried everything above a few times and it does work. Can somebody help? My machine: macbook pro running windows XP Print2 alway...
• Frank: I ended up turning off my virus protector to launch the CD Print Tool and everything turned out great. You have been part of an answered prayer in getting a small duplicating mini...
• XploRa: Hi, Is the MG5240 the same printer as the MG 5220 ?...
• Pauline: HI - trouble with a Canon pixma i4600 - shows an error 5200 just as I am about to start printing - so head ovrheating seems strange. Will look in the other comments to try and fin...
• QuadCore: I uploaded the file just now too virus total and this is the result: http://www.virustotal.com/file-scan/report.html?id=5340c571d6af44f552936d67fab609cd23569a38ebafdc9d9355a083a01b...
• QuadCore: Tray E is correct and can be confirmed in the printer properties after the process is complete....
• Chris: Can you please confirm which CD tray is necessary for the Pro9000 Mark II? All the ebay searches I run say I should be purchasing "Tray E", not "Tray G". Is there a consensus on ...
• Frank: My Avira Anti-Virus Protection will not allow me to launch the CD Print Tool. The reason. "Malware found. A virus or unwanted program 'TR/Agent.37273630' was found in the file......
• abhay: I have a canon ix4000 a very fine and good quality printer,working fine but recently displaying error6500,i read Service mode operation procedures i did the same but it still doesn...
• piedad zhunio: por favor necesito ayuda con una canonip4300 que me visualiza el erroe de operacion no c q debo hacer ayudame gracias...
• Carlos: Gracias de antemano. Tengo una Canosn pixma mx860 y sale error 5c20 en display y hace un ruido el carro del papel al conectar. que dobo hacer?...
• Josue: Hola, tengo un problema con la impresora Canon Ip 4700, cuando va a imprimer me da Error 5700, ya cambie la impresora y siempre me tira el error necesito saber como puedo solucio...
• tina: ok, I figured that part out. My computer was trying to print to the old printer. Changed all those settings and it's printing now. So, the problem that I have now is even though...
• tina: Has anyone had a problem with the computer not seeing the connection with the printer? I have a new iP4820 and I followed all of the steps on this site to convert it to be able to...
• Jody Joy: I use my My Canon IP4300 very little. However it was on this morning, then I turned it off. Tried to turn it on again, but it won't come on. I've checked all cords/cables, switched...